Essay/Term paper: New age of technology

Essay, term paper, research paper:  Narrative Essays

New Age of Technology


Technology and computers are increasing factors in the collision repair
industry. With time being a concern for customers in many cases, the work we do
has become easier to manage and faster to produce because of technology. Over
the past ten years, equipment technology has increased our productivity. Today,
a computerized management system helps you to quickly process repair orders,
job costing, and management reporting. Some examples of this new technology are
the Shark, Pro Spot PR-10, Magna Rack III, and HVLP.
The first example, the Shark, is a computer driven measuring system
designed to be operated electronically. Shark is not a modified mechanical or
laser system. This is a totally new measuring system designed to be computer
driven using ultrasound technology. Unlike mechanical or laser systems, the
beam does not need to be level or parallel when it is placed under the vehicle
The intelligence of the system automatically calibrates its position in relation
to the points being measured. The system re-calibrates itself to the vehicle
every time you measure. If you reposition the beam after the first measurement,
or if the car moves, the beam will automatically re-calibrate from its new
position, still producing the same measurement results.
Before repairs, Shark provides you with the ability to prove existing
damage. This information is good to the vehicle owner and insurance company
because it not only explains the cost of repair, but eliminates unnecessary work
and surprises.
During the straightening procedure, Shark will monitor selected
underbody and upperbody reference points. Shark then calculates deviations from
the manufactures specifications. You can view the whole pulling process, as it
happens, live on the colored monitor. When the job is complete, you may command
Shark to store or print a report in a variety of formats that you can select,
recording the condition of the vehicle as it leaves your shop.
Another example is the revolutionary, Pro Spot PR-10 resistance spot
welding system that can add increased profitability and flexibility to any
collision repair shop. By pressing the trigger button, the PR-10 electronically
provides precise control of the squeeze time, current sensing pre-heat, weld
deviation, hold time, cool down and duty cycle. Within seconds, this cycle is
completed and you can begin another weld. There is no possibility of an
operator rushing a weld because of the pre-timed programming. The operator must
wait until the green light has turned on before doing the next weld. The PR-10
assures you of consistent, properly timed welds whether it is the first weld or
the hundred and fiftieth weld.
With the PR-10 there is no shielding gas or wire to replace and dark
glasses and hoods are a thing of the past. Now you can have clear safety
glasses and actually see the work as it is in process.
Next to be introduced is the Magna Rack III. This is engineered to
perform repairs on damaged light framed and unibodied vehicles with the
hydraulic tilt fixture. With the full-sized platform, everything from unitized
vehicles to pickup trucks and vans fit nicely. Loading ramps can stay attached
to the platform or be removed quickly for unproved vehicle access. The system
has two working heights to choose from.
Magna Rack III adds to your productivity with its full open oval design;
you have complete access to the vehicle. The Magna Rack III performs
combination front, rear or side correction pulls easily. When you need to work
on the underside of the vehicle, the long center opening allows easy access for
anchoring, measuring and welding procedures. Magna Rack III conveniently fits
into a standard size working bay, while enabling you to perform controlled
pulling techniques anywhere around the vehicle. You get maximum flexibility
with the Magna Rack III pulling towers. Each tower assembly easily moves 360
degrees around the Magna Rack III's oval platform.
Next is the HVLP, or High Volume, Low Pressure gun. The HVLP gun has a
design that features hogged-out passages which cause the pressure to drop.
However, there is enough air volume to transfer paint to the surface of a car.
While high solids and waterborne finishes are advancements and are
produced in an effort to reduce damage to the environment from paint and
solvents, there is no more effective VOC reduction tool than HVLP spraygun. The
High volume, low pressure gun design puts a higher percentage of material on the
car because the lower air pressure limits the scattered spray and bounce-back
tendencies of standard equipment. This reduces the waste which ends up on your
exhaust filters and in the atmosphere. The lower pressures used by HVLP
equipment does not develop the strength to create the small droplets the
conventional guns do. Consequently, the finishes can appear "peely". This
condition can be helped with a combination of proper set-up, longer flash times,
slower gun travel and slower reducers. A slower reducer will allow the material
to remain as a liquid for a longer period of time allowing the paint film to
flow. However, the newest generation of HVLP sprayguns outperform the early
versions of the equipment with regard to atomization. So, one may find it
unnecessary to slow the drying with reducers.
Cost saving with use of HVLP equipment are as great as 30 percent, and
less masking is required. A primer-surface application usually requires
complete protection from the overspray. However, an application with HVLP
equipment can be performed with as little as 18 inches of masking surrounding
the repair, saving money. Conventional equipment gives the glass-like finishes
our customers have come to expect. The droplets are smaller and the pressure is
enough to slam them into submission. However, more material gets bounced off
the surface of the car than remains on its surface. Since the droplets in the
paint film are larger with HVLP, the finish can appear "peely". Lower air
pressure can not shear the paint droplets as effectively. The longer the paint
is wet, the better it flows. However, the longer the paint is wet, the greater
the chance of runs. Coordination of temperatures, flash times and reducers is a
must.
This new age of technology has increased so rapidly in the past few
years. It has kept us up to date and has increased all productivity. The old
body man's way of doing things along with the strain and sweat are a thing of
the past